12.2. Central section of a guard
Removal
| PERFORMANCE ORDER |
| 1) remove a bumper |
| 2) remove a front grille |
|
3) remove the decorative panel |
| 4) pull out a guard from the condensing rings |
|
Installation
Carry out installation upside-down:
| PERFORMANCE ORDER |
|
1) unscrew an air duct of the cooling air and fastening from a radiator above |
| 2) remove the central section of a guard |
|
Forward guard, removal
| PERFORMANCE ORDER |
| 1) remove a bumper |
| 2) remove a front grille |
|
3) unscrew the decorative panel (arrows) |
| 4) pull out a guard from the condensing ring to the right or to the left |
|
Forward guard, Sedan
1. A bolt with a six-sided head, 23 N. of m.
2. The self-cutting screw, 7.5 N. of m.
3. Guard, lower section
it is possible to remove together with the central section
4. The self-cutting screw, 7.5 N. of m.
5. A bolt with a six-sided head, 23 N. of m. |
6. The bearing lock plate, it is possible to remove together with the central or lower section
7. A metal ear, at removal of a guard pull it directly down for a corner
8. The self-cutting screw, 7.5 N. of m.
9. Guard, central section |
Forward guard, removal for the Sedan model
| PERFORMANCE ORDER |
|
1) through an opening for access remove the holder of a rope and disconnect a rope |
|
2) unscrew screws of a casing of stitched air (arrow) |
|
3) to remove a guard, pull it under a wing down |
|
Forward guard, installation
Carry out installation upside-down.
Forward wing, removal
| PERFORMANCE ORDER |
| 1) remove a front bumper |
| 2) remove laying of a cavity of a wheel |
|
3) remove the condensing laying (shooter) |
|
Forward wing, removal. Adjustment of a forward wing, cowl gap
| PERFORMANCE ORDER |
|
unscrew fixing bolts and the self-cutting screws |
|
Forward wing, installation
You carry out installation upside-down. Pay attention to the following:
| PERFORMANCE ORDER |
|
1) establish a rivet for a basic arm of a cowl (arrow A) |
| 2) establish a rivet for a stopper of a door (arrow B) |
|
3) establish strips of a sealing cord, 1, 2 and sheet laying with a bolt And on a stopper
1 = 480 mm in length and 7.0 mm in the diameter
2 = 250 mm in length and 7.0 mm in the diameter
|
|
Prevention
The sealing cord will need to be squeezed to diameter in 7.0 mm
Adjustment of a forward wing, cowl gap
| PERFORMANCE ORDER |
| 1) weaken all bolts of a wing |
|
2) having weakened bolts, adjust a gap, moving a wing
and = 4.5 + 1.0 mm |
|
Forward guard assembled for Coupet's models
1. A bolt with a six-sided head, 23 N. of m.
2. The self-cutting screw with a washer
3. Guard, central section |
4. Guard, lower section
5. The self-cutting screw with a washer |
Forward guard, removal for Coupet's model
| PERFORMANCE ORDER |
| 1) remove a bumper |
| 2) remove a front grille |
| 3) disconnect a cowl rope |
|
4) unscrew screws of a decorative covering (arrow) and pull out it from the condensing ring |
|
5) unscrew an air duct of the cooling air and an arm of a radiator (arrow) |
| 6) unscrew an arm of the oil heater |
| 7) disconnect the switch of a lamp of motor office |
| 8) disconnect a connecting loop on the guard panel |
|
9) unscrew the directing device of the soaked-up air (arrow) |
|
Cowl rope, detachment for the Sedan model
| PERFORMANCE ORDER |
|
|
1) through an opening for access remove the holder of a rope and disconnect a rope
|
| 2) unscrew screws of a casing of stitched air (arrow) |
| 3) through an opening for access disconnect the holder of a rope 1 |
| 4) disconnect a rope from an arm 2 |
|
Forward guard, installation. The central section of a guard, removal / installation for Coupet's model
| PERFORMANCE ORDER |
|
to remove a guard, pull it under a wing (shooter) down |
|
Forward guard, installation
Carry out installation upside-down.
Central section of a guard, removal
| PERFORMANCE ORDER |
| 1) remove a bumper |
| 2) remove a front grille |
| 3) disconnect a cowl rope |
|
4) unscrew screws of a decorative covering (arrow) and pull out it from the condensing ring |
|
5) unscrew an air duct of the cooling air and an arm of a radiator (arrow) |
| 6) unscrew and remove the central section of a guard |
|
Central section of a guard, installation
Carry out installation upside-down.
