a43d3481

12:10. Back door (Coupet's model)

Back door in assembly (Coupet's model)
1. Six-sided nut, 8 N. of m.
2. Locking plate; has the contact switch of a lamp of a luggage carrier
3. A bolt with a flat head and a washer, 4 N. of m.
4. Adjusting washer
5. The condensing laying
6. Lock washer
7. Hinge
8. Laying
9. Six-sided nut, 21 N. of m. 		10. Basis
11. Hinge axis
12. Washer
13. Bolt, 10 N. of m.
14. Gas-filled rack
15. Clip, 10 N. of m.
16. Bolt; onboard a body
17. Washer; onboard a body
18. Sealing ring; onboard a body
19. Clip; on the body boat

Back door, removal (Coupet's model)

PERFORMANCE ORDER
1) remove a decorative covering from a frame of a back part of a roof
2) remove a decorative covering of a back door
3) disconnect a screen wiper of back glass
4) remove a plait of wires from a back door
5) extend a block cable connector of a screen wiper of back glass from a cavity
Prevention

For simplification of installation of the flexible pipeline of a washer, attach it to a back door a wire.
6) disconnect a jet of a washer and remove the pipeline

Back door, installation (Coupet's model)

Carry out installation upside-down.

Back door, assembly
1. The condensing laying of a groove of a window
removal is possible only at the bracket removed from a door
2. 8 N. of m.
3. The condensing laying
it is fixed by means of the AKD 476 KD5 05 all-purpose adhesive
4. Door covering
5. The extending clamp
6. Shock-proof fittings
7. 8 N. of m.
8. The lower loop of the lock with the limiter of opening of a door 		9. Top loop of a door
10. 30 N. of m.
11. Overlay of a groove of a door
only on Audi-90 models
for removal pull out from the top part of an upholstery of a door
installation: clear a groove by means of a cleaner
place the pressurizing substance 3.0 mm thick in a groove
establish a slip on a covering of a door and pressure her for installation in the relevant provision

Side part of a body

Arrangement of elements

PERFORMANCE ORDER
1) press on 1 against the stop
2) tighten the screw 2 with an internal hexagon of 0.4 N. of m.
3) close the hatch for installation of all components in initial situation
4) tighten the screw with an internal hexagon of 6 N. of m.

Back door, adjustment

Arrangement of elements

PERFORMANCE ORDER
1) adjust a locking plate 1 to and = 12.0±1.0 mm
2) tighten 2 with m 0.4 N.' moment.
3) close a back door for installation of all components in initial situation
4) open a back door and tighten 2 with m 6 N.' moment.

Lock of a back door, assembly (Coupet's model)

1. Locking plate
contains the contact switch of a lamp of a luggage carrier
adjustment: place a locking plate in the center and tighten with the moment 0.8 N. of m.
close a luggage carrier for centering and alignment of a locking plate
slightly slightly open and tighten six-sided nuts of a shock plate
2. Six-sided nut, 8 N. of m.
3. Draft of lever transfer
do not establish with a tension; maximum free wheeling of 2.0 mm		 4. Transitional plug
5. Plug
6. Laying
7. Plug
displace it for fixing of draft of lever transfer
8. Six-sided nut, 4 N. of m.
9. Lock cylinder
10. Lock
11. Six-sided nut, 8 N. of m.