6. Exhaust system
Exhaust system, arrangement of components (4-cylinder models)
|
1. A tube for measurement WITH
2. A tube cap for measurement WITH 3. 25 N. of m. 4. Final collector 5. 30 N. of m. 6. Consolidation always replace 7. 35 N. of m. 8. 40 N. of m. 9. Average muffler average and back mufflers are installed at the plant as a uniform detail, spare average and back mufflers are delivered separately together with the tightening coupling 10. Fixing ring preliminary tightness: about 7 mm pay attention to arrows in a tab A 11. Depth of introduction "and" has to be at least 42.5 mm 12. Tightening coupling 13. 40 N. of m. 14. Fixing rings preliminary tightness: about 12 mm 15. Back muffler |
16. The place of a section for replacement it is noted by cuts (3) on a circle of a connecting pipe cut a pipe at right angle to a pipe axis in the established situation the section can be made a chain saw the section can also be made, having removed system to remove the exhaust system, weaken a clip ahead of the average muffler and fastening of the left lower shock-absorber, also lower a back axis 17. Tightening coupling 18. 40 N. of m. 19. Catalytic converter 20. A tube for measurement WITH 21. Oxygen sensor (50 N. of m) cover a carving with structure of G5 do not allow G5 to get to cuts on the sensor case 22. Basic arm it is attached to transmission 23. 25 N. of m. 24. Exhaust pipe |
Prevention
1. 20 N. of m. 14. 25 N. of m.
Exhaust system, arrangement of components (5-cylinder models)
2. 30 N. of m.
3. 25 N. of m.
4. Final collector
5. Consolidation
6. 35 N. of m.
7. 25 N. of m.
8. Spring
9. Sealing ring
always replace
10. Tightening coupling
depth of introduction "and" has to be at least 42.5 mm
11. Fixing rings
preliminary tightness: about 7 mm
pay attention to arrows in a tab A
12. Average muffler
13. Back muffler
average and back mufflers are installed at the plant as a uniform detail, spare average and back mufflers are delivered separately together with the tightening coupling
14. Fixing ring
preliminary tightness: about 12 mm15. The place of a section for replacement
it is noted by cuts (3) on a circle of a connecting pipe
cut a pipe at right angle to a pipe axis
in the established situation the section can be made a chain saw
the section can also be made, having removed system
to remove the exhaust system, weaken a clip ahead of the average muffler and fastening of the left lower shock-absorber, also lower a back axis
16. 40 N. of m.
17. 40 N. of m.
18. Tightening coupling
19. Catalytic converter
20. Oxygen sensor (50 N. of m)
cover a carving with structure of G5
do not allow G5 to get to cuts on the sensor case
21. Basic arm
it is attached to transmission
22. Forward exhaust pipe
23. A tube for measurement WITH
Exhaust system, arrangement of components (Coupet's model)
1. Laying
replace
2. 10 N. of m.
3. Heat-shielding screen
4. 25 N. of m.
5. A tube for measurement WITH
6. 30 N. of m.
7. Final collector
8. Oxygen sensor (50 N. of m)
9. Ring consolidation, replace
10. Catalytic converter 11. Tightening coupling
12. Fixing rings
when replacing make sure that new rings correspond to old
13. Back muffler
14. Forward exhaust pipe
15. Fixing rings
when replacing make sure that new rings correspond to old
16. Central muffler
The exhaust system, arrangement of components for all-wheel drive (4х4) models
2. 30 N. of m.
3. 25 N. of m.
4. Final collector
5. Consolidation
6. 35 N. of m.
7. 25 N. of m.
8. Spring
9. Sealing ring
10. 40 N. of m.
11. Fixing ring
12. Average muffler
13. Sealing ring
always replace 14. 25 N. of m.
15. Fixing ring
preliminary tightness: about 12 mm
16. Back muffler
17. Tightening coupling
18. Catalytic converter
19. Oxygen sensor (50 N. of m)
cover a carving with structure of G5
20. Basic arm
it is attached to transmission
21. Forward exhaust pipe
22. A tube for measurement WITH
Prevention
The exhaust system, arrangement of components for 20-klapannny models
2. A hose to the heater of the soaked-up air
3. Heat-shielding screen
4. A tube for measurement WITH
5. Valve of the recirculation of exhaust gases (REG)
6. Vacuum tube of RVG
7. Bolts of "banjo", 20 N. of m.
9. Final cranked branch pipe
10. Main pipe
11. 30 N. of m.
12. Fixing ring
preliminary tightness: about 8 mm
13. Jet muffler
15. 30 N. of m.
16. Oxygen sensor, 50 N. of m.
cover a carving with structure of G5, but do not allow structure to get to cuts on the sensor case
17. 20 N. of m.
18. Catalytic converter
19. 25 N. of m.
20. Sealing washer, 20 N. of m.
21. Tightening coupling, 40 N. of m.
22. 25 N. of m.
23. Tightening coupling, 40 N. of m.
24. Back muffler
Vacuum connections (Coupet's model)
1. Return fuel-supply line
2. The giving fuel-supply line
3. Head of cylinders
4. Ventilating hoses of a case
5. To the device of blocking of differential
6. Throttle case
7. A cover of the soaked-up air
8. Air batcher 9. Coal filter
10. Pressure regulator
11. Locking valve
12. Electromagnetic valve of the coal filter
13. Inlet collector
14. Idling stabilization valve
15. Air filter
Vacuum connections (Audi-90 models)
1. The electromagnetic valve (N 80) for the coal filter
2. Throttle case
3. RVG valve
4. Fuel injector
5. Locking valve
6. Ventilation of a case
7. To the fuel tank
8. Fuel distributor
9. From the fuel filter
10. Inlet collector
11. Idling stabilization valve
12. Head of cylinders
13. Vacuum connection of the amplifier of the brake system 14a. A cap (cars with the forward drive without conditioner)
14b. Connections of the conditioner or blocking of differential
14 pages. Connections of blocking of differential (all-wheel drive cars with the conditioner)
14d. Connection of the conditioner (all-wheel drive cars with the conditioner)
15. Vacuum tank
16. RVG frequency valve (N 121)
17. Coal filter