11.8. System of hydrostrengthening of steering
The pump of the hydraulic booster of steering for 4-cylinder models
| 1. 20 N. of m. 2. Arm 3. 20 N. of m, always replace 4. Arm 5. 20 N, m. 6. Arm 7. 20 N. of m. 8. Maple belt, size: 9.5 h850 mm 9. Bolt and fixing nut 10. 20 N. of m. 11. A pulley, establish by the mark "5Z" forward 12. 25 N. of m. 13. 20 N. of m. 14. Bladed pump before installation fill the soaking-up part with hydraulic liquid and rotate the pump that liquid began to come out the output channel |
15. Bolt of "banjo", inhaling moment: 50 Km 16. Sealing ring always replace 17. The soaking-up hose 18. 19. Bolt of "banjo", inhaling moment: 50 N. of m. 20. Hose of high pressure 21. Arm 22. 20 N. of m. |
The pump of the hydraulic booster of steering for 5-cylinder models
| 1. Bolt of "banjo" inhaling moment: 50 N. of m. 2. Sealing ring always replace 3. 20 N. of m. 4. Arm 5. Arm 6. Maple belt size: 12.5kh992mm 7. 20 N. of m. 8. Pulley establish by the mark "5Z" forward 9. 20 N. of m. 10. Tension device 11. 20 N. of m. 12. Самоконтрящаяся nut inhaling moment: 20 N. of m. |
13. Pump of the hydraulic booster of rulevy management before installation fill the soaking-up part with hydraulic liquid and rotate the pump that liquid began to come out the output channel 14. Arm 15. Tube of high pressure 16. Sealing ring always replace 17. Bolt of "banjo", inhaling moment: 45 Nanometers. 18. The soaking-up hose 19. 20 N. of m. 20. Sealing ring |
Tank of the hydraulic booster of steering
| 1. Hose of the return pipeline 2. Collar 3. The tank is filled with hydraulic liquid check liquid level in a tank (on marks on the tank) after the engine works within 2 minutes, wheels at the same time have to stand directly kill the engine, check the level of liquid and add to mark MOVE if it is necessary |
4. Collar 5. The soaking-up hose 6. Filter clean the cleaning solution 7. Spring clamp it is put on the probe for measurement of level of liquid 8. Spring 9. Uplotnitelno ring 10. Cover of a jellied opening |
Pump of system of hydrostrengthening of steering
| 1. Laying plate * it is inserted into laying 2. Laying * 3. A plate with openings 4. Lock ring * 5. 15 N. of m. grease with D6 sealant before installation longer end twists in a pump housing 6. Check a pump shaft with a flange for existence of scratches and wear tracks if it is necessary, replace all pump remove a rotor and a shaft for replacements of a sealing ring 7. Sealing ring * for replacement, it is necessary to disassemble the pump 8. Case oil channels (are specified by an arrow) both halves of the case have to coincide after assembly 9. Sealing ring * 10. Rotor 11. Blades the polished surface (it is specified by an arrow) has to be turned outside 12. Stator provision of installation: the arrow on the stator has to be visible after installation 13. Valve clamp akkumratno remove by means of a small otverkta 14. The restrictive valve, do not sort 15. Spring 16. Case |
The dual hydraulic pump for model with the 20-valvate engine
| 1. A bolt for a tension of a maple belt 2. Clip 3. 20 N. of m. 4. Rotary arm 5. 20 N. of m. 6. Z0n.m. during the untwisting or removal, always replace with a detail 100 067 04 7. Mobile arm 8. 20 N. of m. 9. 20 N. of m. 10. Maple belt, size: 12.5x992 mm 11. A pulley, establish by a mark "5Z" forward |
12. 10 N. of m. 13. The pump with two pistons systems of a servousileniye of brakes 14. Bladed pump before installation, fill the soaking-up part with hydraulic liquid and rotate the pump that liquid began to come out the output channel 15. The return pipeline, from a tee 16. The tube of high pressure, goes to a steering lath 17. 50 N. of m. 18. 20 N. of m. 19. 35 N. of m. 20. Tube of high pressure |