a43d3481

8.4.2. Lever and rope of the lever of gear shifting

Switching lever gear shifting transfers / Rope

1. Plug
2. Spring
3. Gear shifting lever arm
put a layer of AKD 512001 sealant between an arm and a casing of the transmission at installation
4. Gear shifting lever casing
5. The locking solenoid of automatic gear shifting
6. Switching rope arm
7. Sealing ring
8. Lock ring
9. Gear shifting rope
10. Angular arm of a rope of switching
 11. Cover
12. Switch of bulbs of neutral, parking transfers and transfer of a backing
13. 8 N. of m.
14. Rope clip
15. The switching lever
16. Coupling
17. Plug
18. Lock ring
19. Spring
20. Centering pin
21. Gear shifting lever
22. Plug
Prevention

Before work with the working engine, always move the gear shifting lever to situation P (parkings) and put the car on the emergency brake.

Disconnect a wire of the negative plug of the accumulator before work with any of elements of system of electric equipment.

It is necessary to press a brake pedal before the lever of gear shifting can be removed from parking transfer.

Do not bend and do not overwind a rope. Grease the ends of a rope before installation.

Installation / adjustment
PERFORMANCE ORDER
1) delay fastening of a rope on a rope arm to 15 N. of m.
2) establish a rope in a clip for a rope before installation of an angular arm
3) move the gear shifting lever to situation P
4) weaken a rope clip nut
5) move the switching lever to situation P (back against the stop)
6) tighten a rope clip nut to 8 N. of m.

Mechanism of the lever of gear shifting and rope of gear shifting
1. Gear shifting lever handle
2. Gear shifting lever casing
establish by designation P forward
establish after adjustment of the electromagnetic switch
3. Electromagnetic switch
4. Cover
5. 5 N. of m.
6. The torsion spring
7. Plug
8. Washer
9. Lever switch
gear shiftings
check: the engine has to be started when the lever
switchings is
in the provision of P or N
headlights of a backing have to light up at inclusion of transfer of a backing.
If is not present, turn the switch in a nest and again check its work
10. Basis
at installation put a layer of A/CD 512 001 sealant between the basis and a body
11. Clip bolt
12. Arm
13. Lock ring 		14. Gear shifting lever rope
with a guide and the plug
grease the ends of a rope before installation, tighten a nut of fastening of a rope on an arm to 15 N. of m.
check that the going tube densely sat
for adjustment move the gear shifting lever in situation P
move the switching lever on the transmission in situation P (against the stop back)
tighten a rope clip nut to 20 N. of m.
15. Cover
16. Coupling
17. Washer
18. Plug
19. Coupling
20. Boss
21. Spring clamp
22. 20 N. of m.
23. The switching lever
24. Washer
25. Plug
26. Compression spring
install on the switching lever before installation of the directing pin
27. Plug
28. The directing pin
29. The gear shifting lever with a fork for locking of the lever in the provision of P or N
Prevention

Disconnect a wire of the negative plug of the accumulator before work with any of car electric equipment elements.

Installation of an arm of the lever of gear shifting in relation to the gear shifting lever

PERFORMANCE ORDER
1) install the probe A, 0.8 mm thick, between the lever of gear shifting and the electromagnetic switch
2) press the electromagnetic switch to the probe and tighten a fastening nut
3) after installation of the electromagnetic switch, establish the lower opening of a fork of the lever of gear shifting on the center and give tension on the switch
4) the pin of the solenoid will close a fork
5) establish a gear shifting lever casing so that the lever of gear shifting was opposite to a mark N in a casing (neutral transfer)
6) install the lever A by means of a pin or a drill

In = a pin, with a diameter of 4.0 mm, inserted into a casing opening
7) switch the gear shifting lever to situation in situation N
8) install the switch so that fastening (it is specified by an arrow) was fixed on the gear shifting lever
9) tighten fastening bolts to 5 N. of m.

10) remove a pin or a drill

After installation of the switch, check its work.