10.1. Mechanical components
Support of forward brakes – Girling|
1. 35 N. of m.
always replace hold the directing pin at an inhaling and untwisting 2. Support do not remove a brake hose when replacing brake shoes 3. Thermal screen is established on the piston 4. Arm of brake shoes is on sale as the spare part with previously greased directing pins if protective caps were damaged, replace them with caps from a repair kit, a detail 443 698 470 |
5. Brake shoes always replace four blocks at once (on both wheels) topshchina (new brake shoes): 14:00 mm wear limit: 2.00 mm wear limit (including fixing plates): 7.00 mm 6. Brake disk replace at the same time both disks remove a support before removal of a disk diameter of a brake disk: 256.00 mm thickness (the ventilated disk): 22:00 mm wear limit: 20:00 mm 7. A bolt with a gear head, 125 N. of m clean teeths if you are going to use an old bolt |
Prevention
Support of forward brakes – Giriing – for all-wheel drive and models with 20-valvate engines, and also Coupet's models
|
1. Support
do not remove a brake hose when replacing brake shoes use a press for pressing in of the piston support and old brake shoes for introduction of the piston to the cylinder 2. 35 N.m. always replace hold the directing pin at an inhaling and untwisting 3, 4. Brake shoes always replace four blocks at once (on both wheels) after replacement of brake shoes press a brake pedal several times at the motionless car thickness (new brake shoes): 13:00 mm wear limit: 2.00 mm wear limit (including fixing plates): 7.00 mm |
5. Brake disk replace at the same time both disks remove a brake support before removal of a disk diameter of a brake disk: 276.00 mm thickness: 25.00 mm wear limit: 23:00 mm 6. Arm of brake shoes is on sale as the spare part with previously greased directing pins if protective caps were damaged, replace them with caps from a repair kit, a detail 443 689 470 7. 125 N. of m. |
Prevention
Support of forward brakes – Teves
|
1. Cap
2. The directing pin, 25 N. of m. 3. Support do not remove a brake hose when replacing brake shoes 4. A bolt with a gear head, 125 N. of m. clean teeths if you are going to use an old bolt 5. Arm of brake shoes |
6. Brake shoes always replace four blocks at once (on both wheels) thickness of new brake shoes): 14:00 mm wear limit: 2.00 mm wear limit (including fixing plates): 7.00 mm 7. Brake disk always replace brake disks on both wheels at once remove a support for removal of a disk diameter of a brake disk: 256.00 mm thickness: 22:00 mm wear limit: 20:00 mm 8. Thermal screen is established on the piston |
Support of back brakes – Girling
|
1. Spring clip
holds a brake napkovochnogo rope on a fixing arm 2. Rope of a parking brake 3. 65 N. of m. 4. Brake disk always replace brake disks on both wheels for removal of a disk at once diameter of a brake disk: 245.00 mm thickness: 10:00 mm wear limit: 8.00 mm 5. Brake shoes always replace four blocks at once (on both wheels) thickness (new brake shoes): 12:00 mm wear limit: 2.00 mm wear limit (including fixing plates): 7.00 mm |
6. Arm of brake shoes is on sale as the spare part with previously greased directing pins if protective caps were damaged, replace them with caps from a repair kit, a detail 443 698 470 7. Support remove from an arm of brake shoes when replacing blocks do not remove a brake hose when replacing brake shoes at release models after January, 1989 diameter of the piston of a support is equal to 38 mm when replacing use a support only the required type (with the piston of the required diameter) 8. 35 N. of m. always replace |
Prevention
Technical characteristics
| Models with the forward drive | ||
| Engine |
4-or 5-cylinder
| |
| Diameter of the main brake cylinder |
22.2 mm
| |
| Diameter of the amplifier |
228.9 mm
| |
| Amount of brake fluid (approximately) |
0.6 liter
| |
|
Forward wheels
|
Back wheels
| |
| Diameter of the piston of a support of a brake |
54 mm
|
36 mm
|
| Diameter of a brake disk |
256 mm
|
245 mm
|
| Thickness of a brake disk |
22 mm
|
10 mm
|
| Thickness of brake shoes |
14 mm
|
12 mm
|
| Total area of four brake shoes |
200 cm2
|
120 cm2
|
| All-wheel drive models | ||
| Engine |
5-cylinder
| |
| Diameter of the main brake cylinder |
22.2 mm for models with the 136 h.p. engine.
| |
|
23.81 mm for models with the 170 h.p. engine.
| ||
|
25.4 mm for Coupet's models
| ||
| Diameter of the amplifier |
228.9 mm for models with the 136 h.p. engine.
| |
| Diameter of the piston of the servo-driver of brakes |
24 mm for models with the 170 h.p. engine.
| |
| Amount of brake fluid (approximately) |
0.6 liter
| |
|
Forward wheels
|
Back wheels
| |
| Diameter of the piston of a support of a brake |
54 mm
|
36 mm
|
|
40/45 mm (for Coupet's models)
|
38 mm for release models after January, 1989
| |
|
38 mm for models with the 170 h.p. engine.
|
| |
| Diameter of a brake disk |
256 mm
|
245 mm
|
|
276 mm (for Coupet's models)
|
| |
| Thickness of a brake disk |
22 mm
|
10 mm
|
|
25 mm (for Coupet's models)
|
| |
| Thickness of brake shoes |
14 mm
|
12 mm
|
|
13 (for Coupet's models)
|
| |
| Total area of four brake shoes |
194 cm2
|
108 cm2
|
|
224 cm2 (for Coupet's models)
|
| |
Prevention